Minelab EXPLORER II Manual de servicio Pagina 35
- Pagina / 112
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
THE MINELAB EXPLORER II
29
4
CONTROL PANEL
Power
Figure 4.1
The POWER button turns the Explorer II on and off and also allows
you to specify operation in the detector’s last manual setting.
NOTE The first time you turn on the detector it will start up
with factory presets as the most recent manual setting.
To start the detector in factory preset mode:
• Press and hold the POWER button until a six-note musical
tune is sounded. The Minelab logo and the words ‘FACTORY
PRESETS’ will be briefly displayed on the screen.
To start the detector with its previous manual setting:
• Press and release the POWER button. This will start the
detector with the previous settings from when the detector
was last used (e.g. target specifications, sensitivity levels,
etc) and you may proceed with detecting or modifying
detector settings.
Backlight
Figure 4.2
Pressing the BACKLIGHT button turns the light behind the
Explorer display screen on or off. Contrast can be adjusted to suit
via the Main Menu (detailed in Chapter 5: Quickstart). Turning this
light off will extend battery life. Whenever the detector is switched
on, the backlight illuminates for the first 5 seconds.
POWER AND BACKLIGHT BUTTONS
Figure 4.1 Power button
The Power button offers you the option of operating the Explorer II with its factory
settings or in the most recent manual setting. The backlight provides greater screen
clarity in dim conditions.
POWER AND BACKLIGHT BUTTONS
Figure 4.2 Backlight button
POWER
P0400b
BACKLIGHT
P0401b
- Minelab Explorer II 1
- TABLE OF CONTENTS 3
- Introduction 7
- ABOUT THIS MANUAL 8
- Contact Minelab 9
- MINELAB’S UNIQUE TECHNOLOGY 10
- Getting Lost? 11
- Discrimination 12
- Operating Frequencies 13
- THE MINELAB EXPLORER II 14
- Assembly 15
- ASSEMBLING THE DETECTOR 16
- CONNECTING THE SEARCH COIL 17
- THE SHAFT ASSEMBLY 19
- CONNECTING THE SHAFT ASSEMBLY 20
- Coil not connected? 21
- THE HANDLE ASSEMBLY 22
- Headphone 24
- Pull Coil Cable 26
- Batteries 27
- THE BATTERY PACK 28
- Safety Tip 29
- Recharging 29
- BATTERY PERFORMANCE 31
- Battery Life 31
- More detecting time? 31
- Battery Performance 31
- Control Panel 33
- THE CONTROL PANEL 34
- BACKLIGHT 35
- MENU AND BACK BUTTONS 36
- SHORTCUT BUTTONS 37
- Iron Mask 38
- Pinpoint 38
- SHIFT BUTTONS 39
- Quickstart 41
- GETTING STARTED 42
- Display memory 42
- INCORRECT 43
- QUICKSTART DISPLAY 44
- QUICKSTART’S SMARTFIND 46
- THE IRON MASK 49
- Iron Mask Shortcut 49
- Operating in Iron Mask 50
- Figure 5.6 50
- QUICKSTART’S DIGITAL DISPLAY 51
- Preferred Display 51
- MODIFYING THE DISPLAY 52
- ADJUSTING SENSITIVITY 53
- Noise Cancel 53
- ADJUSTING THRESHOLD 54
- Display Icon 54
- AUDIO RESPONSE 55
- Headphones Caution! 55
- AUDIO MENU 56
- Headphones 56
- AUDIO: ADJUSTING THE VOLUME 57
- Figure 5.16, 5.17 58
- AUDIO: ADJUSTING THE TONE 59
- AUDIO: ADJUSTING THE SOUNDS 60
- PINPOINTING THE OBJECT 63
- Using Pinpoint 64
- Figure 5.21 64
- RECOVERING THE OBJECT 65
- Fill your holes! 65
- SELECTING TARGETS 66
- ADVANCED MODE OPTION 69
- Advanced Use 71
- ADVANCED MODE’S MAIN MENU 72
- STARTING IN ADVANCED MODE 73
- Are you ready? 73
- ADVANCED MODE’S DISPLAYS 74
- ADVANCED MODE’S LEARN DISPLAY 75
- LEARNING TARGETS 76
- Silence please! 76
- LEARN’S TARGET SELECTION 77
- ADVANCED MODE’S EDIT DISPLAY 79
- EDITING PATTERNS 80
- Continued next page 81
- EDITING AND SAVING TARGETS 82
- ADVANCED MODE’S SELECT MENU 83
- SAVING TARGETS 84
- Saving Shortcut 84
- Volume Shortcut 85
- OPTIONS MENU 86
- OPTIONS: NOISE 87
- Noise Shortcut 87
- OPTIONS: RESPONSE 88
- OPTIONS : RESPONSE 89
- OPTIONS: RECOVERY 90
- SETTINGS MENU 91
- Get into the habit 92
- User Info 93
- HELPFUL HINTS 94
- Leading Alkaline 96
- USER PREFERENCES 97
- QUICKSTART MENU STRUCTURE 100
- ADVANCED MENU STRUCTURE 101
- TROUBLESHOOTING 102
- SERVICE REPAIR FORM 103
- WARRANTY 105
- EXPLOPLORER II 106
- EXPLORER II MODEL 107
- GLOSSARY OF TERMS 108
- DETECTOR CARE AND SAFETY 112
Relacionado con productos y manuales para De medición, control y control Minelab EXPLORER II
(25 paginas)
(94 paginas)
(11 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales