Minelab X-Terra 505 Manual de instrucciones Pagina 84
- Pagina / 96
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
84Understanding your X-TERRA - Technology
Q
A
For many metal detectors, implementing Noise Cancel is
typically a slight shift in operating frequency. If the Noise
Cancel process of the X-TERRA is similar, how much of a
frequency shift does each channel of Noise Cancel represent?
It should be noted that operating on a frequency dierent from the resonance
of the coil introduces a phase angle shift, but VFLEX technology accurately
compensates for this and neither Ground Balance nor TID are aected.
Q & A with Laurence
Similar to other metal detectors, the Noise Cancel in X-TERRA
changes the operating frequency of the detector by a small
amount around the resonant frequency of the coil. This
precludes narrow band interfering signals from aecting
the operation of the detector. Because X-TERRA uses pure
sine waves for demodulation, the interference must be very
close to the operating frequency to be a problem. Of course,
broadband interference (like that from car ignition, electric
welding or thunderstorms) cannot be cured with Noise
Cancel, but in this case the very sharp and deep attenuation
of the digital lters helps minimize the eects.
The number of steps (3 or 5) for Noise Cancel depends on the model of detector,
with frequency 0 being always the resonant frequency of the coil, as recorded
in the coils microcontroller during the calibration at the factory. The steps in
frequency depend on the coil frequency, with LF coils having smaller steps and HF
coils having the largest steps:
• LF Noise Cancel frequency step: 35 Hz
• MF Noise Cancel frequency step: 40 Hz
• HF Noise Cancel frequency step: 80 Hz
Noise Cancel Channel
Detector
X-TERRA 305
X-TERRA 505
X-TERRA 705
Coil freq. -2 -1 0 1 2
7.5 kHz
18.75 kHz
7.5 kHz
18.75 kHz
7.5 kHz
18.75 kHz
3 kHz
7.420 kHz 7.460 kHz 7.500 kHz 7.540 kHz 7.580 kHz
18.590 kHz 18.670 kHz 18.750 kHz 18.830 kHz 18.910 kHz
2.930 kHz 2.965 kHz 3.000 kHz 3.035 kHz 3.070 kHz
3 kHz
7.420 kHz 7.460 kHz 7.500 kHz 7.540 kHz 7.580 kHz
18.590 kHz 18.670 kHz 18.750 kHz 18.830 kHz 18.910 kHz
2.930 kHz 2.965 kHz 3.000 kHz 3.035 kHz 3.070 kHz
7.420 kHz 7.460 kHz 7.500 kHz 7.540 kHz 7.580 kHz
18.590 kHz 18.670 kHz 18.750 kHz 18.830 kHz 18.910 kHz
- Understanding your 1
- Contents 2
- 3
- Greetings from Digger 4
- Product Timeline 5
- Product Comparison 6
- Minelab’s Documentation 8
- 9
- Battery Status 10
- Noise Cancel Channel 11
- Threshold 12
- Sensitivity 14
- 15
- MINELAB WARNING!!!! 16
- 17
- Manual Ground Balance 18
- 19
- 19
- 19
- 19
- Auto Ground Balance 20
- Tracking 21
- Tracking Ground Balance Oset 22
- 23
- 23
- Beach Ground Balance 24
- 25
- 26
- 26
- 27
- Discrimination Patterns 28
- Target ID Stability 29
- 30
- 30
- 33
- Treasure Talk 34
- Audio Tones 38
- 39
- 39
- 39
- Hunting by ear 40
- 43
- Coil Options 44
- (not compatible with 45
- X-TERRA 305) 45
- Coil Applications 47
- 6-Inch Concentric Coil 51
- 6-Inch Double-D Coil 51
- X-TERRA 52
- Coil Design & Manufacture 56
- 59
- 60
- 60
- 60
- 61
- Choosing the Right Coil 61
- 61
- 61
- The Hunt 62
- 63
- Pinpointing 64
- Pinpoint Sizing - X-TERRA 705 65
- Full response 65
- Masked response 65
- My Three Rules of Consistency 66
- 2. Consistent Sound 67
- To Dig, or Not to Dig? 68
- My Recommendation 69
- Gold Prospecting 70
- 71
- Minelab’s VFLEX Technology 72
- 73
- 75
- 75
- Q & A with Laurence 79
- Time delay (phase) diagram 81
- 85
- My Settings 86
- 87
- 87
- 87
- 88
- 7 8 9 10 88
- Glossary of Terms 90
- Conclusion 92
- 93
- 93
- 93
- 93
- 93
- Dear Reader 94
- Doc name: RHUYXT2011 95
- About the Author 96
Comentarios a estos manuales
Relacionado con productos y manuales para De medición, control y control Minelab X-Terra 505
(35 paginas)Sony VPCY115FX/BI podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Nie Sony VPCY115FX/BI.
Dostarczamy 1 pdf podręczników Sony VPCY115FX/BI do pobrania za darmo według typów dokumentów: Instrukcja Szybki Start
[email protected]